0330 000 0000 Email our team

Order by 4pm for next working day delivery*

Full 4.1m lengths to your door

Free next day delivery*

Pay in 3 interest-free withKlarna.
Show prices Inc. VAT
0
Show prices
Call 0330 000 0000
0
  • Oak Endgrain Classic Laminate Worktop, Oak Endgrain Classic colour swatch
studioShowing: 38mm square edge, 3m contract

studio · 5414 AW· AW

Oak Endgrain Classic Laminate Worktop

A golden, honey-toned oak showing a panel of concentric growth rings, as though the timber was cut across, with knots in the grain around it. This 38mm square edge laminate worktop is the lighter wood effect of the endgrain pair.

Thickness and edge
Size

What's an upstand?

Upstand, 100mm highWorktop 100mm high 22mm thick Silicone bead 600mm deep worktop Wall

What it is

A 100mm-high strip in Oak Endgrain Classic, the same decor as your worktop. It sits along the back edge of the worktop, against the wall.

Why you need one

Walls are rarely straight, so there's nearly always a gap between worktop and wall. An upstand covers it, stops water and crumbs getting down the back, and gives a neat finished line. It's the simplest, cheapest way to finish a worktop.

Sizes

    Most kitchens need one length per wall run.

    Fitting

    Cut it to length with a fine-tooth saw and bond it to the wall with grab adhesive. Run a bead of clear or matching silicone along the bottom edge, and finish any exposed ends with an end cap.

    Upstand or splashback?

    Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

    Read the full fitting guide

    What's a splashback?

    Splashbackupstand heightHob and oven 640mm high 10mm thick Worktop Wall

    What it is

    A full-height panel in Oak Endgrain Classic, the same decor as your worktop, fixed to the wall behind the hob or sink.

    Why choose one

    One continuous wipe-clean surface with no grout lines, so there's nothing to stain or scrub between tiles. It protects the wall from splashes and cooking grease, and makes the worktop and wall look like one piece.

    Sizes

      Behind a hob

      Check the minimum clearance to a laminate panel in your hob's installation manual. Gas hobs usually need more space, or a heat-resistant panel behind the burners.

      Fitting

      Cut it to size and bond it to a flat, sound wall with panel adhesive. Seal the bottom edge to the worktop with silicone.

      Upstand or splashback?

      Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

      Read the full fitting guide

      What's an edging strip?

      BeforeCut end: barechipboard core AfterEdging strip,45mm wide, coversa cut end

      What it is

      A strip in Oak Endgrain Classic that covers the cut end of the worktop. It comes pre-glued, or is fixed with contact adhesive.

      When you need it

      Whenever a cut end is on show: at the end of a run, on a breakfast bar, or anywhere you've cut a length down.

      Sizes

        Fitting

        1. Glue Spread contact adhesive on the end and the strip, or warm a pre-glued strip.
        2. Press Press it on firmly from the middle outwards, with a block of wood.
        3. Trim and file Trim the overhang with a sharp blade, then file the edges down at a slight angle.
        Read the full fitting guide

        What are joining strips?

        Corner strip (L-shape)Straight stripSeen from above Aluminium strip38mm worktop: use the38mm stripWorktopWorktop

        What it is

        An aluminium strip that joins two worktop lengths without a router or jig. The web slips between the two ends and the cap covers the joint.

        Straight or corner

        Straight: joins two lengths in a line. Corner: makes an L-shaped join where two runs meet.

        Sizes

          Match the strip to your worktop's thickness: a 38mm strip for a 38mm worktop.

          The alternative

          A mason's mitre gives a seamless corner, but it needs a worktop jig and a router. See both options in our fitting guide.

          Read the full fitting guide

          What are end caps?

          BeforeAfterExposed endEnd capScrewed over therounded profile Left end capRight end capYou, facing the worktopWall

          What it is

          An aluminium cap that finishes the exposed end of a postformed worktop, following its rounded front edge.

          Left or right?

          Stand facing the worktop. If the exposed end is on your left, you need a left end cap; if it's on your right, a right end cap.

          Sizes

            Match the cap to your worktop's thickness.

            Fitting

            Hold the cap against the end, drill small pilot holes and screw it on. A thin bead of silicone behind it keeps water out of the end.

            Read the full fitting guide

            What's in the joint kit?

            3 connector boltsJoint sealant Seen from underneathBolts pull the joint tight;sealant keeps water out

            What's in it

            Three connector bolts and a tube of joint sealant: everything to hold one worktop joint together.

            What it's for

            The bolts sit in pockets cut underneath both worktops and pull the joint tight. The sealant goes on the joint faces first, so water can't get into the core.

            How many?

            One kit per worktop joint.

              Read the full fitting guide
              Total inc VAT £128.78

              Free delivery on this order

              4 interest-free payments of £32.19
              or 3 interest-free payments of £42.92

              18+, UK residents, subject to status. Borrowing more than you can afford or paying late may affect your ability to get credit.

              Order by 4pm for next working day delivery*

              • 38mm square edge, no thinner option
              • Finish AW, chipboard core below
              • Upstand 100mm high, splashback 600mm high
              • Worktop 620mm deep, bar top 900mm deep
              • Free deliveryNext working day to most of the UK*
              • Full lengthsDelivered uncut, ready to fit
              • Pay your wayCard, Clearpay or Klarna
              Description

              A golden, honey-toned oak showing a panel of concentric growth rings, as though the timber was cut across, with knots in the grain around it. This 38mm square edge laminate worktop is the lighter wood effect of the endgrain pair.

              Delivery

              Delivered by our specialist worktop delivery partner, in full lengths, flat and protected. Delivery is free to every postcode we serve. Order by 4pm Monday to Friday for next working day delivery to most of England and Wales; orders placed after 4pm, at weekends or on bank holidays are dispatched the next working day, and some areas take 2 to 3 working days. Check your date below. We confirm your slot 24 hours before, and delivery is kerbside, so have a second person ready to carry it in.
              Returns

              Changed your mind? You have 14 days from delivery to return it unused, uncut and in its wrapping; we refund within 14 days of getting it back. Report any damage within 48 hours. Full returns policy.

              Care and cleaning

              Clean with warm soapy water, then wipe dry. Light golden oak hides most marks, but dried splashes of tea still leave rings, so wipe them while fresh. Use a board for chopping.

              Which edge?

              • Postformed: the laminate wraps a soft, rounded front. Classic and hard-wearing.
              • Square edge: a sharp, modern line with a matching edge strip.
              • Compact: 12mm solid board, slim and waterproof.
              More on edges and thickness

              Fitting in four steps

              • Measure, then cut face down with a fine-tooth blade.
              • Lay it on the units and screw up through the brackets.
              • Seal the cut edges, then fit the upstand and end caps.
              Read the full fitting guide

              How to measure

              • Measure each wall run along the back, in millimetres.
              • Add about 50mm to every run so you can trim to a clean fit.
              • In an L-shape, let the longest run go into the corner.
              Full measuring guide

              Size guide

              • Worktops come 3000mm or 4100mm long and 600mm deep.
              • Breakfast bars are deeper: 665mm or 900mm, for islands and overhangs.
              • Buy a length that covers your run, then cut it to fit.
              Full sizes and heights guide

              Why you’ll love it

              • Honey oak with a growth-ring panel

                Light golden-brown grain surrounds a set of tree rings and a handful of knots. It reads as a natural, sunlit oak with one distinctive feature, rather than an even stripe.

              • Sturdy surface, finish AW

                Finish AW is a laminate that shrugs off stains and everyday scratches and needs no oil or seal. Cut ends should be capped with edging strip to protect the chipboard core.

              • Matching set in the same print

                An upstand (3000 x 100 x 20mm) and splashback (3000 x 600 x 6mm) match. A full-length 3050 x 900mm breakfast bar carries the rings across an island.

              Sunlit oak for family kitchens

              The lighter tone suits cream, white, pale blue and sage cabinets, and the rings keep it from feeling flat. In a family kitchen the busy figure hides daily wear, and in a utility room it brightens a small space. If you prefer a deeper brown with the same ring pattern, Endgrain Cognac sits alongside it in the range. Sizes and trims are identical.

              Compare oak effect worktops

              How to fit

              Fitting Oak Endgrain Classic

              Oak Endgrain Classic is a single 38mm square edge. The golden ring panel is easy to position, but it should not be split by a cut or hidden under a hob, so lay the lengths out first.

              What you’ll need

              Most homes have these already:

              • Pencil
              • Drill driver
              • Circular saw or jigsaw
              • Straight edge or spirit level

              Tap to add the brands fitters use to your order:

              Rather not do it yourself? Any local kitchen fitter can fit it, and our team is happy to help on 0330 000 0000.

              Sizes and prices

              Prices include VAT and free delivery. Oak Endgrain Classic is supplied in full 3m and 4.1m lengths, uncut.

              ProductSize (L x D x T)Price
              Worktop 3.05m · 38mm square edge, 3m contract 3050 × 620 × 38mm £128.78
              Breakfast bar 900mm · 38mm square edge, 3m contract 3050 × 900 × 38mm £218.09
              Matching upstand · 3m 3000 × 100 × 20mm £53.27
              Edging strip · 43mm ABS edging Per metre £5.77
              Joining strips · Straight 38mm Aluminium, 38mm × 640mm £9.99
              Joining strips · Corner 38mm Aluminium, 38mm × 640mm £11.99
              End caps · Left 38mm Aluminium, 38mm × 640mm £7.99
              End caps · Right 38mm Aluminium, 38mm × 640mm £7.99
              Fitting kit · Joint kit 3 connector bolts + sealant £12.99

              Specification

              Brandstudio
              Decor code5414
              FinishAW
              EdgeSquare edged
              Thickness38mm
              Depth620mm; breakfast bars 900mm
              Lengths3050mm
              CoreChipboard core under a high-pressure laminate surface
              Matching upstand3000 x 100 x 20mm
              Matching splashback3000 x 600 x 6mm
              WarrantyManufacturer’s warranty

              Questions about Oak Endgrain Classic

              Can’t find your answer? Contact our worktop team.

              0330 000 0000Email us
              What are the available dimensions?

              Oak Endgrain Classic is 38mm thick, 3050mm long, with a 620mm-deep worktop and a 900mm-deep breakfast bar. No 22mm version is listed.

              What is the difference from Endgrain Cognac?

              Both use the ring panel and the same sizes. This one is a lighter, golden oak, while Cognac is a deeper, redder brown.

              Are the growth rings repeated on each length?

              The ring panel is part of a printed decor and falls differently on each length. Check each one before cutting so you can place the feature where it shows.

              Does it suit a white kitchen?

              Very well. White shaker doors with golden oak feel fresh and traditional, and brushed brass or black handles both work.

              Can I tackle the corner joint myself?

              Yes, with a butt joint held by connector bolts and sealed. It is a straightforward job for a competent DIYer, though a fitter will finish faster.

              Is an inset sink fine in this worktop?

              An inset sink is the right choice here. Seal the cut-out edges fully with silicone, and avoid undermount sinks, which would expose the chipboard core.

              More oak & wood looks

              View all

              Kitchen Ideas, New Colours & The Odd Offer

              One email a month, written by people who know worktops. Unsubscribe whenever you like.

              By signing up you agree to receive marketing emails. Read our privacy policy.

              Your basket (0)

              Your basket is empty.

              Shop worktops

              Your delivery postcode

              We’ll use it to show your delivery dates across the site.