0330 000 0000 Email our team

Order by 4pm for next working day delivery*

Full 4.1m lengths to your door

Free next day delivery*

Pay in 3 interest-free withKlarna.
Show prices Inc. VAT
0
Show prices
Call 0330 000 0000
0
  • Hazel Silverjack Oak Laminate Worktop, Hazel Silverjack Oak colour swatch
Kronospan FinesseShowing: 38mm square edge

Kronospan Finesse · K544 RW· Rift Wood

Hazel Silverjack Oak Laminate Worktop

A weathered, silvery-brown oak, somewhere between taupe and driftwood, with long grain lines and the odd knot. These oak effect worktops are laminate with a crisp 38mm square edge. A matching upstand and splashback finish the look without any solid-wood upkeep.

Thickness and edge
Size

What's an upstand?

Upstand, 100mm highWorktop 100mm high 22mm thick Silicone bead 600mm deep worktop Wall

What it is

A 100mm-high strip in Hazel Silverjack Oak, the same decor as your worktop. It sits along the back edge of the worktop, against the wall.

Why you need one

Walls are rarely straight, so there's nearly always a gap between worktop and wall. An upstand covers it, stops water and crumbs getting down the back, and gives a neat finished line. It's the simplest, cheapest way to finish a worktop.

Sizes

    Most kitchens need one length per wall run.

    Fitting

    Cut it to length with a fine-tooth saw and bond it to the wall with grab adhesive. Run a bead of clear or matching silicone along the bottom edge, and finish any exposed ends with an end cap.

    Upstand or splashback?

    Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

    Read the full fitting guide

    What's a splashback?

    Splashbackupstand heightHob and oven 640mm high 10mm thick Worktop Wall

    What it is

    A full-height panel in Hazel Silverjack Oak, the same decor as your worktop, fixed to the wall behind the hob or sink.

    Why choose one

    One continuous wipe-clean surface with no grout lines, so there's nothing to stain or scrub between tiles. It protects the wall from splashes and cooking grease, and makes the worktop and wall look like one piece.

    Sizes

      It's double-sided: Vintage Silverjack Oak is on the reverse, so you can choose which way round to fit it.

      Behind a hob

      Check the minimum clearance to a laminate panel in your hob's installation manual. Gas hobs usually need more space, or a heat-resistant panel behind the burners.

      Fitting

      Cut it to size and bond it to a flat, sound wall with panel adhesive. Seal the bottom edge to the worktop with silicone.

      Upstand or splashback?

      Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

      Read the full fitting guide

      What's an edging strip?

      BeforeCut end: barechipboard core AfterEdging strip,45mm wide, coversa cut end

      What it is

      A strip in Hazel Silverjack Oak that covers the cut end of the worktop. It comes pre-glued, or is fixed with contact adhesive.

      When you need it

      Whenever a cut end is on show: at the end of a run, on a breakfast bar, or anywhere you've cut a length down.

      Sizes

        Fitting

        1. Glue Spread contact adhesive on the end and the strip, or warm a pre-glued strip.
        2. Press Press it on firmly from the middle outwards, with a block of wood.
        3. Trim and file Trim the overhang with a sharp blade, then file the edges down at a slight angle.
        Read the full fitting guide

        What are joining strips?

        Corner strip (L-shape)Straight stripSeen from above Aluminium strip38mm worktop: use the38mm stripWorktopWorktop

        What it is

        An aluminium strip that joins two worktop lengths without a router or jig. The web slips between the two ends and the cap covers the joint.

        Straight or corner

        Straight: joins two lengths in a line. Corner: makes an L-shaped join where two runs meet.

        Sizes

          Match the strip to your worktop's thickness: a 38mm strip for a 38mm worktop.

          The alternative

          A mason's mitre gives a seamless corner, but it needs a worktop jig and a router. See both options in our fitting guide.

          Read the full fitting guide

          What are end caps?

          BeforeAfterExposed endEnd capScrewed over therounded profile Left end capRight end capYou, facing the worktopWall

          What it is

          An aluminium cap that finishes the exposed end of a postformed worktop, following its rounded front edge.

          Left or right?

          Stand facing the worktop. If the exposed end is on your left, you need a left end cap; if it's on your right, a right end cap.

          Sizes

            Match the cap to your worktop's thickness.

            Fitting

            Hold the cap against the end, drill small pilot holes and screw it on. A thin bead of silicone behind it keeps water out of the end.

            Read the full fitting guide

            What's in the joint kit?

            3 connector boltsJoint sealant Seen from underneathBolts pull the joint tight;sealant keeps water out

            What's in it

            Three connector bolts and a tube of joint sealant: everything to hold one worktop joint together.

            What it's for

            The bolts sit in pockets cut underneath both worktops and pull the joint tight. The sealant goes on the joint faces first, so water can't get into the core.

            How many?

            One kit per worktop joint.

              Read the full fitting guide
              Total inc VAT £168.73

              Free delivery on this order

              4 interest-free payments of £42.18
              or 3 interest-free payments of £56.24

              18+, UK residents, subject to status. Borrowing more than you can afford or paying late may affect your ability to get credit.

              Order by 4pm for next working day delivery*

              • 38mm square edge, colour-matched ABS
              • Rift Wood texture, decor K544
              • 100mm upstand, splashback and edging strip
              • Lengths of 3m and 4.1m, bars to 900mm deep
              • Free deliveryNext working day to most of the UK*
              • Full lengthsDelivered uncut, ready to fit
              • Pay your wayCard, Clearpay or Klarna
              Description

              A weathered, silvery-brown oak, somewhere between taupe and driftwood, with long grain lines and the odd knot. These oak effect worktops are laminate with a crisp 38mm square edge. A matching upstand and splashback finish the look without any solid-wood upkeep.

              Delivery

              Delivered by our specialist worktop delivery partner, in full lengths, flat and protected. Delivery is free to every postcode we serve. Order by 4pm Monday to Friday for next working day delivery to most of England and Wales; orders placed after 4pm, at weekends or on bank holidays are dispatched the next working day, and some areas take 2 to 3 working days. Check your date below. We confirm your slot 24 hours before, and delivery is kerbside, so have a second person ready to carry it in.
              Returns

              Changed your mind? You have 14 days from delivery to return it unused, uncut and in its wrapping; we refund within 14 days of getting it back. Report any damage within 48 hours. Full returns policy.

              Care and cleaning

              Wipe this oak effect with a soft cloth and warm soapy water, following the grain. Dry any water around the sink. Use a chopping board and a trivet, because heat and blades mark any laminate.

              Which edge?

              • Postformed: the laminate wraps a soft, rounded front. Classic and hard-wearing.
              • Square edge: a sharp, modern line with a matching edge strip.
              • Compact: 12mm solid board, slim and waterproof.
              More on edges and thickness

              Fitting in four steps

              • Measure, then cut face down with a fine-tooth blade.
              • Lay it on the units and screw up through the brackets.
              • Seal the cut edges, then fit the upstand and end caps.
              Read the full fitting guide

              How to measure

              • Measure each wall run along the back, in millimetres.
              • Add about 50mm to every run so you can trim to a clean fit.
              • In an L-shape, let the longest run go into the corner.
              Full measuring guide

              Size guide

              • Worktops come 3000mm or 4100mm long and 600mm deep.
              • Breakfast bars are deeper: 665mm or 900mm, for islands and overhangs.
              • Buy a length that covers your run, then cut it to fit.
              Full sizes and heights guide

              See the whole board

              The full 4100 × 600mm board, so you can see how the pattern runs from end to end.

              Full 4100mm board of Hazel Silverjack Oak Laminate Worktop, showing how the grain runs along the length

              Swipe to see the full length

              Hazel Silverjack Oak Laminate Worktop: full board

              Full 4100mm board of Hazel Silverjack Oak Laminate Worktop, showing how the grain runs along the length

              Why you’ll love it

              • Driftwood tones with long, open grain

                The colour leans grey-brown rather than orange, with darker streaks and small knots along the board. It looks like oak that has weathered for years, so it feels calm and natural rather than polished.

              • Rift Wood texture, laminate toughness

                The decor is named for Kronospan's Rift Wood finish and sits on a laminate face over a chipboard core. Spills wipe off, and no oiling or sealing is needed, unlike real timber.

              • Pairs with Vintage Silverjack Oak

                The 4100 x 640 x 10mm splashback is double-sided with Vintage Silverjack Oak, the deeper brown. A 4100 x 100 x 20mm upstand and breakfast bars complete the set.

              A grey-leaning oak for modern and country kitchens

              Hazel Silverjack suits painted units in sage, stone and off-white, and it softens a handleless kitchen that might otherwise feel cold. Because the oak leans grey, it also sits comfortably against black taps and slate floors. It is a good pick if you want a wood look but find honey and orange oaks too warm, and a sensible match for a utility room.

              Explore oak and wood effect worktops

              How to fit

              Fitting Hazel Silverjack Oak

              Hazel Silverjack Oak is a 38mm square-edge board with a visible grain running its full length. Keep the grain heading the same way on every run, and have the 43mm edging strip ready for each cut end.

              What you’ll need

              Most homes have these already:

              • Pencil
              • Drill driver
              • Circular saw or jigsaw
              • Straight edge or spirit level

              Tap to add the brands fitters use to your order:

              Rather not do it yourself? Any local kitchen fitter can fit it, and our team is happy to help on 0330 000 0000.

              Sizes and prices

              Prices include VAT and free delivery. Hazel Silverjack Oak is supplied in full 3m and 4.1m lengths, uncut.

              ProductSize (L x D x T)Price
              Worktop 3m · 38mm square edge 3000 × 600 × 38mm £168.73
              Worktop 4.1m · 38mm square edge 4100 × 600 × 38mm £229.08
              Breakfast bar 665mm · 38mm square edge 4100 × 665 × 38mm £368.92
              Breakfast bar 900mm · 38mm square edge 4100 × 900 × 38mm £366.53
              Matching upstand · 4.1m 4100 × 100 × 20mm £86.80
              Matching upstand · 3m 3000 × 100 × 20mm £65.97
              Matching splashback · 4.1m 4100 × 640 × 10mm £258.30
              Edging strip · 43mm ABS edging 1300 × 43 × 1.5mm £5.49
              Joining strips · Straight 38mm Aluminium, 38mm × 640mm £9.99
              Joining strips · Corner 38mm Aluminium, 38mm × 640mm £11.99
              End caps · Left 38mm Aluminium, 38mm × 640mm £7.99
              End caps · Right 38mm Aluminium, 38mm × 640mm £7.99
              Fitting kit · Joint kit 3 connector bolts + sealant £12.99

              Specification

              BrandKronospan Finesse
              Decor codeK544
              FinishRift Wood (RW)
              EdgeABS square edge, 1.5mm radius
              Thickness38mm
              Depth600mm; breakfast bars 665mm and 900mm
              Lengths3000mm, 4100mm
              CoreChipboard core under a high-pressure laminate surface
              Matching upstand4100 x 100 x 20mm
              Matching splashback4100 x 640 x 10mm, double-sided with K545RW Vintage Silverjack Oak
              WarrantyManufacturer’s warranty

              Questions about Hazel Silverjack Oak

              Can’t find your answer? Contact our worktop team.

              0330 000 0000Email us
              Is Hazel Silverjack closer to grey or brown?

              It sits in between. The base is a grey-brown taupe, with darker brown streaks in the grain. In cool light it looks silvery. In warm light it picks up more brown.

              What depths do the breakfast bars come in?

              Two depths, both 38mm thick and 4100mm long: 665mm and 900mm. Ordinary boards are 600mm deep, supplied at 3000mm or 4100mm. This decor has no 22mm option.

              How does it compare with Vintage Silverjack Oak?

              They share a name and a grain character. Hazel is lighter and greyer. Vintage is a rich mid-brown. Because they share a double-sided splashback, you can use one for the run and one for the island.

              Do I have to oil it like real wood?

              No. It is a laminate surface with a printed oak grain, so it needs no oil and no sealing. Only the cut ends need attention, and the matching edging strip covers them.

              What cabinet colours work with this oak?

              Sage green, dusty blue, warm white and deep charcoal all work. Black or aged-brass handles pick out the darker streaks in the grain, while chrome gives a cooler feel.

              Can I butt-joint two boards at a corner?

              Yes, square-edge boards can be butted. Pull them tight with connector bolts and fill the joint with colour-matched sealant. Check that the grain flows the same way on both sides.

              More oak & wood looks

              View all

              Kitchen Ideas, New Colours & The Odd Offer

              One email a month, written by people who know worktops. Unsubscribe whenever you like.

              By signing up you agree to receive marketing emails. Read our privacy policy.

              Your basket (0)

              Your basket is empty.

              Shop worktops

              Your delivery postcode

              We’ll use it to show your delivery dates across the site.