0330 000 0000 Email our team

Order by 4pm for next working day delivery*

Full 4.1m lengths to your door

Free next day delivery*

Pay in 3 interest-free withKlarna.
Show prices Inc. VAT
0
Show prices
Call 0330 000 0000
0
  • Pietra Copper Stipple Solid Surface Worktop, Copper Stipple colour swatch
PietraShowing: 25mm solid surface

Pietra

Pietra Copper Stipple Solid Surface Worktop

A pale grey-white solid surface worktop scattered with small copper, tan and grey chips, cast in one colour all the way through. It is 25mm thick, in 3050mm lengths and 900mm-deep breakfast bars. A slim matching upstand finishes the wall edge.

Thickness and edge
Size

What's an upstand?

Upstand, 100mm highWorktop 100mm high 22mm thick Silicone bead 600mm deep worktop Wall

What it is

A 100mm-high strip in Pietra Copper Stipple, the same decor as your worktop. It sits along the back edge of the worktop, against the wall.

Why you need one

Walls are rarely straight, so there's nearly always a gap between worktop and wall. An upstand covers it, stops water and crumbs getting down the back, and gives a neat finished line. It's the simplest, cheapest way to finish a worktop.

Sizes

    Most kitchens need one length per wall run.

    Fitting

    Cut it to length with a fine-tooth saw and bond it to the wall with grab adhesive. Run a bead of clear or matching silicone along the bottom edge, and finish any exposed ends with an end cap.

    Upstand or splashback?

    Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

    Read the full fitting guide

    What's a splashback?

    Splashbackupstand heightHob and oven 640mm high 10mm thick Worktop Wall

    What it is

    A full-height panel in Pietra Copper Stipple, the same decor as your worktop, fixed to the wall behind the hob or sink.

    Why choose one

    One continuous wipe-clean surface with no grout lines, so there's nothing to stain or scrub between tiles. It protects the wall from splashes and cooking grease, and makes the worktop and wall look like one piece.

    Sizes

      Behind a hob

      Check the minimum clearance to a laminate panel in your hob's installation manual. Gas hobs usually need more space, or a heat-resistant panel behind the burners.

      Fitting

      Cut it to size and bond it to a flat, sound wall with panel adhesive. Seal the bottom edge to the worktop with silicone.

      Upstand or splashback?

      Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

      Read the full fitting guide

      What's an edging strip?

      BeforeCut end: barechipboard core AfterEdging strip,45mm wide, coversa cut end

      What it is

      A strip in Pietra Copper Stipple that covers the cut end of the worktop. It comes pre-glued, or is fixed with contact adhesive.

      When you need it

      Whenever a cut end is on show: at the end of a run, on a breakfast bar, or anywhere you've cut a length down.

      Sizes

        Fitting

        1. Glue Spread contact adhesive on the end and the strip, or warm a pre-glued strip.
        2. Press Press it on firmly from the middle outwards, with a block of wood.
        3. Trim and file Trim the overhang with a sharp blade, then file the edges down at a slight angle.
        Read the full fitting guide

        What are joining strips?

        Corner strip (L-shape)Straight stripSeen from above Aluminium strip38mm worktop: use the38mm stripWorktopWorktop

        What it is

        An aluminium strip that joins two worktop lengths without a router or jig. The web slips between the two ends and the cap covers the joint.

        Straight or corner

        Straight: joins two lengths in a line. Corner: makes an L-shaped join where two runs meet.

        Sizes

          Match the strip to your worktop's thickness: a 38mm strip for a 38mm worktop.

          The alternative

          A mason's mitre gives a seamless corner, but it needs a worktop jig and a router. See both options in our fitting guide.

          Read the full fitting guide

          What are end caps?

          BeforeAfterExposed endEnd capScrewed over therounded profile Left end capRight end capYou, facing the worktopWall

          What it is

          An aluminium cap that finishes the exposed end of a postformed worktop, following its rounded front edge.

          Left or right?

          Stand facing the worktop. If the exposed end is on your left, you need a left end cap; if it's on your right, a right end cap.

          Sizes

            Match the cap to your worktop's thickness.

            Fitting

            Hold the cap against the end, drill small pilot holes and screw it on. A thin bead of silicone behind it keeps water out of the end.

            Read the full fitting guide

            What's in the joint kit?

            3 connector boltsJoint sealant Seen from underneathBolts pull the joint tight;sealant keeps water out

            What's in it

            Three connector bolts and a tube of joint sealant: everything to hold one worktop joint together.

            What it's for

            The bolts sit in pockets cut underneath both worktops and pull the joint tight. The sealant goes on the joint faces first, so water can't get into the core.

            How many?

            One kit per worktop joint.

              Read the full fitting guide
              Total inc VAT £538.14

              Free delivery on this order

              4 interest-free payments of £134.53
              or 3 interest-free payments of £179.38

              18+, UK residents, subject to status. Borrowing more than you can afford or paying late may affect your ability to get credit.

              Order by 4pm for next working day delivery*

              • 25mm acrylic, one material throughout
              • Copper and tan chips on a pale ground
              • Matching 12mm upstand, 3050mm long
              • Worktops at 3050mm, bars at 2000mm
              • Free deliveryNext working day to most of the UK*
              • Full lengthsDelivered uncut, ready to fit
              • Pay your wayCard, Clearpay or Klarna
              Description

              A pale grey-white solid surface worktop scattered with small copper, tan and grey chips, cast in one colour all the way through. It is 25mm thick, in 3050mm lengths and 900mm-deep breakfast bars. A slim matching upstand finishes the wall edge.

              Delivery

              Delivered by our specialist worktop delivery partner, in full lengths, flat and protected. Delivery is free to every postcode we serve. Order by 4pm Monday to Friday for next working day delivery to most of England and Wales; orders placed after 4pm, at weekends or on bank holidays are dispatched the next working day, and some areas take 2 to 3 working days. Check your date below. We confirm your slot 24 hours before, and delivery is kerbside, so have a second person ready to carry it in.
              Returns

              Changed your mind? You have 14 days from delivery to return it unused, uncut and in its wrapping; we refund within 14 days of getting it back. Report any damage within 48 hours. Full returns policy.

              Care and cleaning

              Wash with warm soapy water and dry with a soft cloth. If the speckled surface picks up a light scratch, work the care kit pads over it in small circles. Put a trivet under hot pans.

              Which edge?

              • Postformed: the laminate wraps a soft, rounded front. Classic and hard-wearing.
              • Square edge: a sharp, modern line with a matching edge strip.
              • Compact: 12mm solid board, slim and waterproof.
              More on edges and thickness

              Fitting in four steps

              • Measure, then cut face down with a fine-tooth blade.
              • Lay it on the units and screw up through the brackets.
              • Seal the cut edges, then fit the upstand and end caps.
              Read the full fitting guide

              How to measure

              • Measure each wall run along the back, in millimetres.
              • Add about 50mm to every run so you can trim to a clean fit.
              • In an L-shape, let the longest run go into the corner.
              Full measuring guide

              Size guide

              • Worktops come 3000mm or 4100mm long and 600mm deep.
              • Breakfast bars are deeper: 665mm or 900mm, for islands and overhangs.
              • Buy a length that covers your run, then cut it to fit.
              Full sizes and heights guide

              Why you’ll love it

              • Copper, tan and grey chips on pale grey

                Small chips in copper, tan, grey and near-black are spread evenly over a light ground. It reads as a fine terrazzo-style fleck rather than a veined stone.

              • Solid all the way down

                The colour and chips run through the full 25mm, so a trimmed end shows the same pattern as the face. The care kit pads rub light scratches back out.

              • Upstand and island in one decor

                The 3050 x 100 x 12mm upstand matches the top, and the 2000 x 900 x 25mm breakfast bar lets an island carry the same chips as the run.

              A speckled neutral for warm and cool kitchens

              The chip colours bring in warmth without turning the pale ground yellow, so the top sits easily with cream, taupe or soft grey cabinets. Brushed brass or copper handles echo the flecks. The all-over pattern also suits a busy family kitchen, because small chips break up the look of crumbs and light marks. It is a quiet stone effect that never competes with the room.

              See every solid surface worktop

              How to fit

              Fitting Pietra Copper Stipple

              Copper Stipple arrives in full 3050mm lengths, 25mm thick, so plan the run before touching a saw. A single straight length is simple; any bonded joint or corner calls for a fitter with the right adhesive and clamps.

              What you’ll need

              Most homes have these already:

              • Pencil
              • Drill driver
              • Circular saw or jigsaw
              • Straight edge or spirit level

              Tap to add the brands fitters use to your order:

              Rather not do it yourself? Any local kitchen fitter can fit it, and our team is happy to help on 0330 000 0000.

              Sizes and prices

              Prices include VAT and free delivery. Pietra Copper Stipple is supplied in full 3m and 4.1m lengths, uncut.

              ProductSize (L x D x T)Price
              Worktop 3.05m · 25mm solid surface 3050 × 650 × 25mm £538.14
              Breakfast bar 900mm · 25mm solid surface 2000 × 900 × 25mm £511.60
              Matching upstand · 3.05m 3050 × 100 × 12mm £73.67

              Specification

              BrandPietra
              EdgeSolid surface
              Thickness25mm
              Depth650mm; breakfast bars 900mm
              Lengths3050mm
              CoreSolid surface, the same material all the way through
              Matching upstand3050 x 100 x 12mm
              WarrantyManufacturer’s warranty

              Questions about Pietra Copper Stipple

              Can’t find your answer? Contact our worktop team.

              0330 000 0000Email us
              What are the depths of the Copper Stipple top and bar?

              The worktop is 650mm deep and 3050mm long, at 25mm thick. The breakfast bar is 900mm deep and 2000mm long, which leaves room for stools on an island.

              Do the chips wear away at the edges?

              No. The chips are part of the material and run through the full 25mm, not a printed layer. A trimmed end shows the same flecks as the face.

              Which cabinet colours suit copper flecks?

              Warm greys, cream, taupe and muted green all work, and deep navy gives strong contrast. Brass or copper handles pick up the flecks, while black handles lean toward the darker chips.

              Does Copper Stipple suit an undermount sink?

              Yes. Undermount sinks suit solid surface worktops, unlike laminate. Ask your fitter to prepare the cut-out, because the job needs the right adhesive and tools.

              Is this a DIY job?

              A single straight length is manageable. Bonded joints need the right adhesive and clamps, so most people use a fitter experienced with solid surface for anything beyond one piece.

              What if the top picks up a scratch?

              Work the abrasive pads from the care kit over the mark in light circles. Because the colour runs all the way through, buffing does not remove a printed layer.

              More solid surface looks

              View all

              Kitchen Ideas, New Colours & The Odd Offer

              One email a month, written by people who know worktops. Unsubscribe whenever you like.

              By signing up you agree to receive marketing emails. Read our privacy policy.

              Your basket (0)

              Your basket is empty.

              Shop worktops

              Your delivery postcode

              We’ll use it to show your delivery dates across the site.