0330 000 0000 Email our team

Order by 4pm for next working day delivery*

Full 4.1m lengths to your door

Free next day delivery*

Pay in 3 interest-free withKlarna.
Show prices Inc. VAT
0
Show prices
Call 0330 000 0000
0
  • Romeo Laminate Worktop, Romeo colour swatch
DuropalShowing: 38mm postformed

Duropal · S63075 PT· PT

Romeo Laminate Worktop

A creamy ivory marble with warm tan clouds and one dark, branching fissure across the sheet. These laminate worktops come with a 38mm postformed edge or a slim 20mm square edge. A 12mm compact version is also made for sinks.

Thickness and edge
Size

What's an upstand?

Upstand, 100mm highWorktop 100mm high 22mm thick Silicone bead 600mm deep worktop Wall

What it is

A 100mm-high strip in Romeo, the same decor as your worktop. It sits along the back edge of the worktop, against the wall.

Why you need one

Walls are rarely straight, so there's nearly always a gap between worktop and wall. An upstand covers it, stops water and crumbs getting down the back, and gives a neat finished line. It's the simplest, cheapest way to finish a worktop.

Sizes

    Most kitchens need one length per wall run.

    Fitting

    Cut it to length with a fine-tooth saw and bond it to the wall with grab adhesive. Run a bead of clear or matching silicone along the bottom edge, and finish any exposed ends with an end cap.

    Upstand or splashback?

    Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

    Read the full fitting guide

    What's a splashback?

    Splashbackupstand heightHob and oven 640mm high 10mm thick Worktop Wall

    What it is

    A full-height panel in Romeo, the same decor as your worktop, fixed to the wall behind the hob or sink.

    Why choose one

    One continuous wipe-clean surface with no grout lines, so there's nothing to stain or scrub between tiles. It protects the wall from splashes and cooking grease, and makes the worktop and wall look like one piece.

    Sizes

      Behind a hob

      Check the minimum clearance to a laminate panel in your hob's installation manual. Gas hobs usually need more space, or a heat-resistant panel behind the burners.

      Fitting

      Cut it to size and bond it to a flat, sound wall with panel adhesive. Seal the bottom edge to the worktop with silicone.

      Upstand or splashback?

      Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

      Read the full fitting guide

      What's an edging strip?

      BeforeCut end: barechipboard core AfterEdging strip,45mm wide, coversa cut end

      What it is

      A strip in Romeo that covers the cut end of the worktop. It comes pre-glued, or is fixed with contact adhesive.

      When you need it

      Whenever a cut end is on show: at the end of a run, on a breakfast bar, or anywhere you've cut a length down.

      Sizes

        Fitting

        1. Glue Spread contact adhesive on the end and the strip, or warm a pre-glued strip.
        2. Press Press it on firmly from the middle outwards, with a block of wood.
        3. Trim and file Trim the overhang with a sharp blade, then file the edges down at a slight angle.
        Read the full fitting guide

        What are joining strips?

        Corner strip (L-shape)Straight stripSeen from above Aluminium strip38mm worktop: use the38mm stripWorktopWorktop

        What it is

        An aluminium strip that joins two worktop lengths without a router or jig. The web slips between the two ends and the cap covers the joint.

        Straight or corner

        Straight: joins two lengths in a line. Corner: makes an L-shaped join where two runs meet.

        Sizes

          Match the strip to your worktop's thickness: a 38mm strip for a 38mm worktop.

          The alternative

          A mason's mitre gives a seamless corner, but it needs a worktop jig and a router. See both options in our fitting guide.

          Read the full fitting guide

          What are end caps?

          BeforeAfterExposed endEnd capScrewed over therounded profile Left end capRight end capYou, facing the worktopWall

          What it is

          An aluminium cap that finishes the exposed end of a postformed worktop, following its rounded front edge.

          Left or right?

          Stand facing the worktop. If the exposed end is on your left, you need a left end cap; if it's on your right, a right end cap.

          Sizes

            Match the cap to your worktop's thickness.

            Fitting

            Hold the cap against the end, drill small pilot holes and screw it on. A thin bead of silicone behind it keeps water out of the end.

            Read the full fitting guide

            What's in the joint kit?

            3 connector boltsJoint sealant Seen from underneathBolts pull the joint tight;sealant keeps water out

            What's in it

            Three connector bolts and a tube of joint sealant: everything to hold one worktop joint together.

            What it's for

            The bolts sit in pockets cut underneath both worktops and pull the joint tight. The sealant goes on the joint faces first, so water can't get into the core.

            How many?

            One kit per worktop joint.

              Read the full fitting guide
              Total inc VAT £202.58

              Free delivery on this order

              4 interest-free payments of £50.64
              or 3 interest-free payments of £67.52

              18+, UK residents, subject to status. Borrowing more than you can afford or paying late may affect your ability to get credit.

              Order by 4pm for next working day delivery*

              • Two edges: 38mm postformed or 20mm square
              • Finish code PT, cream marble with a dark vein
              • Matching upstand and splashback in cream marble
              • Lengths 3m and 4.1m; 20mm comes in 4.1m only
              • Free deliveryNext working day to most of the UK*
              • Full lengthsDelivered uncut, ready to fit
              • Pay your wayCard, Clearpay or Klarna
              Description

              A creamy ivory marble with warm tan clouds and one dark, branching fissure across the sheet. These laminate worktops come with a 38mm postformed edge or a slim 20mm square edge. A 12mm compact version is also made for sinks.

              Delivery

              Delivered by our specialist worktop delivery partner, in full lengths, flat and protected. Delivery is free to every postcode we serve. Order by 4pm Monday to Friday for next working day delivery to most of England and Wales; orders placed after 4pm, at weekends or on bank holidays are dispatched the next working day, and some areas take 2 to 3 working days. Check your date below. We confirm your slot 24 hours before, and delivery is kerbside, so have a second person ready to carry it in.
              Returns

              Changed your mind? You have 14 days from delivery to return it unused, uncut and in its wrapping; we refund within 14 days of getting it back. Report any damage within 48 hours. Full returns policy.

              Care and cleaning

              Warm soapy water and a soft cloth clean both versions. Dry any water that gathers near the sink, especially along the laser edge. Wipe splashes off the cream surface promptly.

              Which edge?

              • Postformed: the laminate wraps a soft, rounded front. Classic and hard-wearing.
              • Square edge: a sharp, modern line with a matching edge strip.
              • Compact: 12mm solid board, slim and waterproof.
              More on edges and thickness

              Fitting in four steps

              • Measure, then cut face down with a fine-tooth blade.
              • Lay it on the units and screw up through the brackets.
              • Seal the cut edges, then fit the upstand and end caps.
              Read the full fitting guide

              How to measure

              • Measure each wall run along the back, in millimetres.
              • Add about 50mm to every run so you can trim to a clean fit.
              • In an L-shape, let the longest run go into the corner.
              Full measuring guide

              Size guide

              • Worktops come 3000mm or 4100mm long and 600mm deep.
              • Breakfast bars are deeper: 665mm or 900mm, for islands and overhangs.
              • Buy a length that covers your run, then cut it to fit.
              Full sizes and heights guide

              Why you’ll love it

              • Cream marble with a dark fissure

                An ivory ground carries warm tan clouds and one dark, branching crack. It reads as a warm marble with a single dramatic line rather than an all-over pattern.

              • Two thicknesses, one surface

                The same high-pressure laminate comes as a 38mm postformed worktop and a 20mm laser-edged square edge. Both stand up to stains and everyday scratches, and neither wants sealing.

              • A compact version for the sink run

                Romeo also exists as a 12mm compact, which suits an undermount sink. The 4100 x 120 x 19mm upstand and 4100 x 640mm splashback match. See compact worktops.

              Choose the edge to suit the kitchen

              The 38mm postformed edge gives a soft, traditional line that suits Shaker and in-frame doors. The 20mm square edge is slimmer and sharper, which fits flat-fronted, handleless kitchens and refits where you want a lighter look. The warm cream tone sits well with greige, taupe and dark green cabinets. A fitter can mix both thicknesses in one house, perhaps postformed in the kitchen and slim in the utility room.

              See all laminate worktops

              How to fit

              Fitting Romeo

              Romeo comes as 38mm postformed with a 3mm rounded edge, or 20mm square edge with a laser-edged front. The steps differ slightly, so follow the ones that match your thickness.

              What you’ll need

              Most homes have these already:

              • Pencil
              • Drill driver
              • Circular saw or jigsaw
              • Straight edge or spirit level

              Tap to add the brands fitters use to your order:

              Rather not do it yourself? Any local kitchen fitter can fit it, and our team is happy to help on 0330 000 0000.

              Sizes and prices

              Prices include VAT and free delivery. Romeo is supplied in full 3m and 4.1m lengths, uncut.

              ProductSize (L x D x T)Price
              Worktop 3m · 38mm postformed 3000 × 600 × 38mm £151.94
              Worktop 4.1m · 38mm postformed 4100 × 600 × 38mm £202.58
              Worktop 3m, 640 deep · 38mm postformed 3000 × 640 × 38mm Price on request
              Worktop 4.1m, 640 deep · 38mm postformed 4100 × 640 × 38mm Price on request
              Breakfast bar 670mm · 38mm postformed 4100 × 670 × 38mm £286.49
              Breakfast bar 900mm · 38mm postformed 4100 × 900 × 38mm £350.80
              Breakfast bar 3m, 670mm · 38mm postformed 3000 × 670 × 38mm Price on request
              Breakfast bar 3m, 900mm · 38mm postformed 3000 × 900 × 38mm Price on request
              Worktop 4.1m · 20mm square edge 4100 × 640 × 20mm £304.75
              Worktop 4.1m, 600 deep · 20mm square edge 4100 × 600 × 20mm Price on request
              Breakfast bar 900mm · 20mm square edge 4100 × 900 × 20mm £483.26
              Breakfast bar 670mm · 20mm square edge 4100 × 670 × 20mm Price on request
              Matching upstand · 4.1m 4100 × 120 × 19mm £109.74
              Matching upstand · 3m 3000 × 120 × 19mm £83.40
              Matching splashback · 4.1m 4100 × 640mm £269.07
              Edging strip · 45mm laminate edging 4100mm length £6.84
              Edging strip · 25mm ABS edging Per metre £6.84
              Joining strips · Straight 38mm Aluminium, 38mm × 640mm £9.99
              Joining strips · Corner 38mm Aluminium, 38mm × 640mm £11.99
              Joining strips · Straight 22mm Aluminium, 22mm × 640mm £9.99
              Joining strips · Corner 22mm Aluminium, 22mm × 640mm £11.99
              End caps · Left 38mm Aluminium, 38mm × 640mm £7.99
              End caps · Right 38mm Aluminium, 38mm × 640mm £7.99
              End caps · Left 22mm Aluminium, 22mm × 640mm £7.99
              End caps · Right 22mm Aluminium, 22mm × 640mm £7.99
              Fitting kit · Joint kit 3 connector bolts + sealant £12.99

              Specification

              BrandDuropal
              Decor codeS63075
              FinishPT
              EdgePostformed Quadra, 3mm radius; Square edge, laser edged
              Thickness38mm or 20mm
              Depth600mm, 640mm; breakfast bars 670mm and 900mm
              Lengths3000mm, 4100mm
              CoreChipboard core under a high-pressure laminate surface
              Matching upstand4100 x 120 x 19mm
              Matching splashback4100 x 640mm
              Compact version12mm compact laminate also available
              WarrantyManufacturer’s warranty

              Questions about Romeo

              Can’t find your answer? Contact our worktop team.

              0330 000 0000Email us
              Which thickness of Romeo should I choose?

              Choose 38mm for a traditional, rounded front that suits Shaker doors, or 20mm for a slim, crisp square edge on flat-fronted units. The pattern and colour are the same on both.

              What sizes does the 20mm version come in?

              The slim version is listed as a 4100 x 640 x 20mm worktop and a 4100 x 900 x 20mm breakfast bar. It does not come in 3m, so plan your runs around the 4.1m length.

              What sink options does Romeo allow?

              Not in laminate, because the chipboard core would show at the cut-out. Pick an inset sink, or the 12mm compact Romeo, which is solid all the way through and suits an undermount.

              Where does the dark vein fall?

              The swatch shows one prominent dark crack across a cream ground, so its position varies by length. Lay the lengths side by side first and decide which piece should take the focus.

              Which cabinet colours go with warm cream marble?

              Greige, taupe, dark green and soft white all sit well with it. Brass and bronze handles echo the tan clouds in the pattern.

              Do the wall pieces come in the same cream marble?

              Yes. The upstand is 4100 x 120 x 19mm and the splashback 4100 x 640mm, both printed in the same cream marble as the worktop.

              More marble effect looks

              View all

              Kitchen Ideas, New Colours & The Odd Offer

              One email a month, written by people who know worktops. Unsubscribe whenever you like.

              By signing up you agree to receive marketing emails. Read our privacy policy.

              Your basket (0)

              Your basket is empty.

              Shop worktops

              Your delivery postcode

              We’ll use it to show your delivery dates across the site.