0330 000 0000 Email our team

Order by 4pm for next working day delivery*

Full 4.1m lengths to your door

Free next day delivery*

Pay in 3 interest-free withKlarna.
Show prices Inc. VAT
0
Show prices
Call 0330 000 0000
0
  • Charcoal Flow Laminate Worktop, Charcoal Flow colour swatch
Kronospan FinesseShowing: 38mm square edge

Kronospan Finesse · K353 RT· Rust

Charcoal Flow Laminate Worktop

Almost black, with fine vertical streaks running through it like timber that has been burnt and brushed back. This laminate kitchen worktop has a 38mm square edge and a dark presence for modern, moody kitchens. A matching upstand and splashback complete the run.

Thickness and edge
Size

What's an upstand?

Upstand, 100mm highWorktop 100mm high 22mm thick Silicone bead 600mm deep worktop Wall

What it is

A 100mm-high strip in Charcoal Flow, the same decor as your worktop. It sits along the back edge of the worktop, against the wall.

Why you need one

Walls are rarely straight, so there's nearly always a gap between worktop and wall. An upstand covers it, stops water and crumbs getting down the back, and gives a neat finished line. It's the simplest, cheapest way to finish a worktop.

Sizes

    Most kitchens need one length per wall run.

    Fitting

    Cut it to length with a fine-tooth saw and bond it to the wall with grab adhesive. Run a bead of clear or matching silicone along the bottom edge, and finish any exposed ends with an end cap.

    Upstand or splashback?

    Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

    Read the full fitting guide

    What's a splashback?

    Splashbackupstand heightHob and oven 640mm high 10mm thick Worktop Wall

    What it is

    A full-height panel in Charcoal Flow, the same decor as your worktop, fixed to the wall behind the hob or sink.

    Why choose one

    One continuous wipe-clean surface with no grout lines, so there's nothing to stain or scrub between tiles. It protects the wall from splashes and cooking grease, and makes the worktop and wall look like one piece.

    Sizes

      It's double-sided: Platinum Disk is on the reverse, so you can choose which way round to fit it.

      Behind a hob

      Check the minimum clearance to a laminate panel in your hob's installation manual. Gas hobs usually need more space, or a heat-resistant panel behind the burners.

      Fitting

      Cut it to size and bond it to a flat, sound wall with panel adhesive. Seal the bottom edge to the worktop with silicone.

      Upstand or splashback?

      Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

      Read the full fitting guide

      What's an edging strip?

      BeforeCut end: barechipboard core AfterEdging strip,45mm wide, coversa cut end

      What it is

      A strip in Charcoal Flow that covers the cut end of the worktop. It comes pre-glued, or is fixed with contact adhesive.

      When you need it

      Whenever a cut end is on show: at the end of a run, on a breakfast bar, or anywhere you've cut a length down.

      Sizes

        Fitting

        1. Glue Spread contact adhesive on the end and the strip, or warm a pre-glued strip.
        2. Press Press it on firmly from the middle outwards, with a block of wood.
        3. Trim and file Trim the overhang with a sharp blade, then file the edges down at a slight angle.
        Read the full fitting guide

        What are joining strips?

        Corner strip (L-shape)Straight stripSeen from above Aluminium strip38mm worktop: use the38mm stripWorktopWorktop

        What it is

        An aluminium strip that joins two worktop lengths without a router or jig. The web slips between the two ends and the cap covers the joint.

        Straight or corner

        Straight: joins two lengths in a line. Corner: makes an L-shaped join where two runs meet.

        Sizes

          Match the strip to your worktop's thickness: a 38mm strip for a 38mm worktop.

          The alternative

          A mason's mitre gives a seamless corner, but it needs a worktop jig and a router. See both options in our fitting guide.

          Read the full fitting guide

          What are end caps?

          BeforeAfterExposed endEnd capScrewed over therounded profile Left end capRight end capYou, facing the worktopWall

          What it is

          An aluminium cap that finishes the exposed end of a postformed worktop, following its rounded front edge.

          Left or right?

          Stand facing the worktop. If the exposed end is on your left, you need a left end cap; if it's on your right, a right end cap.

          Sizes

            Match the cap to your worktop's thickness.

            Fitting

            Hold the cap against the end, drill small pilot holes and screw it on. A thin bead of silicone behind it keeps water out of the end.

            Read the full fitting guide

            What's in the joint kit?

            3 connector boltsJoint sealant Seen from underneathBolts pull the joint tight;sealant keeps water out

            What's in it

            Three connector bolts and a tube of joint sealant: everything to hold one worktop joint together.

            What it's for

            The bolts sit in pockets cut underneath both worktops and pull the joint tight. The sealant goes on the joint faces first, so water can't get into the core.

            How many?

            One kit per worktop joint.

              Read the full fitting guide
              Total inc VAT £168.73

              Free delivery on this order

              4 interest-free payments of £42.18
              or 3 interest-free payments of £56.24

              18+, UK residents, subject to status. Borrowing more than you can afford or paying late may affect your ability to get credit.

              Order by 4pm for next working day delivery*

              • 38mm square edge in dark charcoal
              • Dark Rust (RT) surface, K353
              • Upstand, splashback and edging, all in charcoal
              • 4.1m runs plus 665mm and 900mm breakfast bars
              • Free deliveryNext working day to most of the UK*
              • Full lengthsDelivered uncut, ready to fit
              • Pay your wayCard, Clearpay or Klarna
              Description

              Almost black, with fine vertical streaks running through it like timber that has been burnt and brushed back. This laminate kitchen worktop has a 38mm square edge and a dark presence for modern, moody kitchens. A matching upstand and splashback complete the run.

              Delivery

              Delivered by our specialist worktop delivery partner, in full lengths, flat and protected. Delivery is free to every postcode we serve. Order by 4pm Monday to Friday for next working day delivery to most of England and Wales; orders placed after 4pm, at weekends or on bank holidays are dispatched the next working day, and some areas take 2 to 3 working days. Check your date below. We confirm your slot 24 hours before, and delivery is kerbside, so have a second person ready to carry it in.
              Returns

              Changed your mind? You have 14 days from delivery to return it unused, uncut and in its wrapping; we refund within 14 days of getting it back. Report any damage within 48 hours. Full returns policy.

              Care and cleaning

              Dark Rust-finish laminate shows dust and water spots, so wipe it daily with a soft cloth and warm soapy water. Dry it afterwards and avoid abrasive pads. Lift pans onto a trivet rather than setting them down hot.

              Which edge?

              • Postformed: the laminate wraps a soft, rounded front. Classic and hard-wearing.
              • Square edge: a sharp, modern line with a matching edge strip.
              • Compact: 12mm solid board, slim and waterproof.
              More on edges and thickness

              Fitting in four steps

              • Measure, then cut face down with a fine-tooth blade.
              • Lay it on the units and screw up through the brackets.
              • Seal the cut edges, then fit the upstand and end caps.
              Read the full fitting guide

              How to measure

              • Measure each wall run along the back, in millimetres.
              • Add about 50mm to every run so you can trim to a clean fit.
              • In an L-shape, let the longest run go into the corner.
              Full measuring guide

              Size guide

              • Worktops come 3000mm or 4100mm long and 600mm deep.
              • Breakfast bars are deeper: 665mm or 900mm, for islands and overhangs.
              • Buy a length that covers your run, then cut it to fit.
              Full sizes and heights guide

              Why you’ll love it

              • Deep charcoal with a streaked grain

                The base is a very dark brown-black. Slightly lighter streaks run along the length, so the surface has depth and movement rather than flat, solid black.

              • Rust finish with a laminate skin

                The Rust finish sits on a high-pressure laminate surface that shrugs off stains and light scratching, with no sealing needed. You should still use a board for chopping and a trivet for pans.

              • Platinum Disk on the splashback reverse

                The matching splashback (4100 x 640 x 10mm) is double-sided with plain mid-grey Platinum Disk. Add the 4100 x 100 x 20mm upstand, and a breakfast bar for an island.

              Dark surfaces for confident kitchens

              A near-black worktop makes pale cabinets look crisper and gives dark units a monochrome, grounded feel. It works well with brushed steel or brass handles, and with open shelves in warm oak. In a rental or a garage conversion it also hides the marks of daily use. The trade-off is that dust and crumbs show up, so a quick daily wipe keeps it sharp.

              Browse black and dark worktops

              How to fit

              Fitting Charcoal Flow

              Charcoal Flow is a 38mm square-edge worktop with a dark decor, so a rough cut shows. Take your time with the saw, support the offcut, and have the 43mm edging strip ready for each exposed end.

              What you’ll need

              Most homes have these already:

              • Pencil
              • Drill driver
              • Circular saw or jigsaw
              • Straight edge or spirit level

              Tap to add the brands fitters use to your order:

              Rather not do it yourself? Any local kitchen fitter can fit it, and our team is happy to help on 0330 000 0000.

              Sizes and prices

              Prices include VAT and free delivery. Charcoal Flow is supplied in full 3m and 4.1m lengths, uncut.

              ProductSize (L x D x T)Price
              Worktop 3m · 38mm square edge 3000 × 600 × 38mm £168.73
              Worktop 4.1m · 38mm square edge 4100 × 600 × 38mm £229.08
              Breakfast bar 665mm · 38mm square edge 4100 × 665 × 38mm £368.92
              Breakfast bar 900mm · 38mm square edge 4100 × 900 × 38mm £366.53
              Matching upstand · 4.1m 4100 × 100 × 20mm £86.80
              Matching upstand · 3m 3000 × 100 × 20mm £65.97
              Matching splashback · 4.1m 4100 × 640 × 10mm £258.30
              Edging strip · 43mm ABS edging 1300 × 43 × 1.5mm £5.49
              Joining strips · Straight 38mm Aluminium, 38mm × 640mm £9.99
              Joining strips · Corner 38mm Aluminium, 38mm × 640mm £11.99
              End caps · Left 38mm Aluminium, 38mm × 640mm £7.99
              End caps · Right 38mm Aluminium, 38mm × 640mm £7.99
              Fitting kit · Joint kit 3 connector bolts + sealant £12.99

              Specification

              BrandKronospan Finesse
              Decor codeK353
              FinishRust (RT)
              EdgeABS square edge, 1.5mm radius
              Thickness38mm
              Depth600mm; breakfast bars 665mm and 900mm
              Lengths3000mm, 4100mm
              CoreChipboard core under a high-pressure laminate surface
              Matching upstand4100 x 100 x 20mm
              Matching splashback4100 x 640 x 10mm, double-sided with K523PE Platinum Disk
              WarrantyManufacturer’s warranty

              Questions about Charcoal Flow

              Can’t find your answer? Contact our worktop team.

              0330 000 0000Email us
              How dark is Charcoal Flow in a real kitchen?

              It is a deep brown-black with slightly lighter streaks, so it is not a flat jet black. In daylight the streaking is visible. In low light it reads as a solid dark surface.

              Which sizes suit an island?

              Breakfast bars are 4100mm long and either 665mm or 900mm deep, both 38mm thick. Plain worktops are 600mm deep and come in 3000mm or 4100mm. Charcoal Flow is not made in 22mm.

              What goes on the other side of the splashback?

              The splashback, 4100 x 640 x 10mm, has two faces. Its reverse is Platinum Disk, code K523 PE, a plain mid-grey. Use the Charcoal Flow face for a dark wall, or flip it for a lighter feel.

              Do I need an edging strip for every cut?

              Yes, on every cut end and cut-out. The 1300 x 43mm Charcoal Flow strip covers the chipboard core and matches the decor, which stops moisture reaching it. A silicone bead seals the wall side.

              Will it suit a garage or utility room?

              It does. The dark, streaked surface is forgiving of daily knocks and wipes clean with soapy water. Seal every cut-out properly, and keep damp mops and standing water away from joints.

              What handle colours work with it?

              Brushed brass and copper stand out strongly against the charcoal. Black handles give a quieter, all-dark kitchen. Stainless steel suits a more industrial look beside it.

              More black & dark looks

              View all

              Kitchen Ideas, New Colours & The Odd Offer

              One email a month, written by people who know worktops. Unsubscribe whenever you like.

              By signing up you agree to receive marketing emails. Read our privacy policy.

              Your basket (0)

              Your basket is empty.

              Shop worktops

              Your delivery postcode

              We’ll use it to show your delivery dates across the site.