0330 000 0000 Email our team

Order by 4pm for next working day delivery*

Full 4.1m lengths to your door

Free next day delivery*

Pay in 3 interest-free withKlarna.
Show prices Inc. VAT
0
Show prices
Call 0330 000 0000
0
  • Carrera Marble Laminate Worktop: decor photo coming soon
TopShapeShowing: 40mm square edge

TopShape

Carrera Marble Laminate Worktop

A marble look from TopShape, supplied in 3600mm lengths rather than 4000mm, which suits shorter kitchens. This marble effect laminate worktop has a decorative square edge, laminated both sides, in 40mm or 25mm, with matching pieces to coordinate the room.

Thickness and edge
Size

What's an upstand?

Upstand, 100mm highWorktop 100mm high 22mm thick Silicone bead 600mm deep worktop Wall

What it is

A 100mm-high strip in Carrera Marble, the same decor as your worktop. It sits along the back edge of the worktop, against the wall.

Why you need one

Walls are rarely straight, so there's nearly always a gap between worktop and wall. An upstand covers it, stops water and crumbs getting down the back, and gives a neat finished line. It's the simplest, cheapest way to finish a worktop.

Sizes

    Most kitchens need one length per wall run.

    Fitting

    Cut it to length with a fine-tooth saw and bond it to the wall with grab adhesive. Run a bead of clear or matching silicone along the bottom edge, and finish any exposed ends with an end cap.

    Upstand or splashback?

    Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

    Read the full fitting guide

    What's a splashback?

    Splashbackupstand heightHob and oven 640mm high 10mm thick Worktop Wall

    What it is

    A full-height panel in Carrera Marble, the same decor as your worktop, fixed to the wall behind the hob or sink.

    Why choose one

    One continuous wipe-clean surface with no grout lines, so there's nothing to stain or scrub between tiles. It protects the wall from splashes and cooking grease, and makes the worktop and wall look like one piece.

    Sizes

      Behind a hob

      Check the minimum clearance to a laminate panel in your hob's installation manual. Gas hobs usually need more space, or a heat-resistant panel behind the burners.

      Fitting

      Cut it to size and bond it to a flat, sound wall with panel adhesive. Seal the bottom edge to the worktop with silicone.

      Upstand or splashback?

      Choose an upstand if you're tiling above the worktop, or want the cheapest neat finish. Choose a splashback behind the hob or sink, or if you want no tiles at all. Lots of kitchens use both.

      Read the full fitting guide

      What's an edging strip?

      BeforeCut end: barechipboard core AfterEdging strip,45mm wide, coversa cut end

      What it is

      A strip in Carrera Marble that covers the cut end of the worktop. It comes pre-glued, or is fixed with contact adhesive.

      When you need it

      Whenever a cut end is on show: at the end of a run, on a breakfast bar, or anywhere you've cut a length down.

      Sizes

        Fitting

        1. Glue Spread contact adhesive on the end and the strip, or warm a pre-glued strip.
        2. Press Press it on firmly from the middle outwards, with a block of wood.
        3. Trim and file Trim the overhang with a sharp blade, then file the edges down at a slight angle.
        Read the full fitting guide

        What are joining strips?

        Corner strip (L-shape)Straight stripSeen from above Aluminium strip38mm worktop: use the38mm stripWorktopWorktop

        What it is

        An aluminium strip that joins two worktop lengths without a router or jig. The web slips between the two ends and the cap covers the joint.

        Straight or corner

        Straight: joins two lengths in a line. Corner: makes an L-shaped join where two runs meet.

        Sizes

          Match the strip to your worktop's thickness: a 38mm strip for a 38mm worktop.

          The alternative

          A mason's mitre gives a seamless corner, but it needs a worktop jig and a router. See both options in our fitting guide.

          Read the full fitting guide

          What are end caps?

          BeforeAfterExposed endEnd capScrewed over therounded profile Left end capRight end capYou, facing the worktopWall

          What it is

          An aluminium cap that finishes the exposed end of a postformed worktop, following its rounded front edge.

          Left or right?

          Stand facing the worktop. If the exposed end is on your left, you need a left end cap; if it's on your right, a right end cap.

          Sizes

            Match the cap to your worktop's thickness.

            Fitting

            Hold the cap against the end, drill small pilot holes and screw it on. A thin bead of silicone behind it keeps water out of the end.

            Read the full fitting guide

            What's in the joint kit?

            3 connector boltsJoint sealant Seen from underneathBolts pull the joint tight;sealant keeps water out

            What's in it

            Three connector bolts and a tube of joint sealant: everything to hold one worktop joint together.

            What it's for

            The bolts sit in pockets cut underneath both worktops and pull the joint tight. The sealant goes on the joint faces first, so water can't get into the core.

            How many?

            One kit per worktop joint.

              Read the full fitting guide
              Total inc VAT £393.24

              Free delivery on this order

              4 interest-free payments of £98.31
              or 3 interest-free payments of £131.08

              18+, UK residents, subject to status. Borrowing more than you can afford or paying late may affect your ability to get credit.

              Order by 4pm for next working day delivery*

              • 3600mm long, in 40mm or 25mm
              • Depths 650mm and 900mm
              • Decorative edge laminated on each side
              • Upstand, utility panel, backsplash, edging
              • Free deliveryNext working day to most of the UK*
              • Full lengthsDelivered uncut, ready to fit
              • Pay your wayCard, Clearpay or Klarna
              Description

              A marble look from TopShape, supplied in 3600mm lengths rather than 4000mm, which suits shorter kitchens. This marble effect laminate worktop has a decorative square edge, laminated both sides, in 40mm or 25mm, with matching pieces to coordinate the room.

              Delivery

              Delivered by our specialist worktop delivery partner, in full lengths, flat and protected. Delivery is free to every postcode we serve. Order by 4pm Monday to Friday for next working day delivery to most of England and Wales; orders placed after 4pm, at weekends or on bank holidays are dispatched the next working day, and some areas take 2 to 3 working days. Check your date below. We confirm your slot 24 hours before, and delivery is kerbside, so have a second person ready to carry it in.
              Returns

              Changed your mind? You have 14 days from delivery to return it unused, uncut and in its wrapping; we refund within 14 days of getting it back. Report any damage within 48 hours. Full returns policy.

              Care and cleaning

              Warm soapy water and a soft cloth are enough for daily cleaning, followed by a dry wipe. Skip bleach and scouring pads. Place a trivet under hot pans.

              Which edge?

              • Postformed: the laminate wraps a soft, rounded front. Classic and hard-wearing.
              • Square edge: a sharp, modern line with a matching edge strip.
              • Compact: 12mm solid board, slim and waterproof.
              More on edges and thickness

              Fitting in four steps

              • Measure, then cut face down with a fine-tooth blade.
              • Lay it on the units and screw up through the brackets.
              • Seal the cut edges, then fit the upstand and end caps.
              Read the full fitting guide

              How to measure

              • Measure each wall run along the back, in millimetres.
              • Add about 50mm to every run so you can trim to a clean fit.
              • In an L-shape, let the longest run go into the corner.
              Full measuring guide

              Size guide

              • Worktops come 3000mm or 4100mm long and 600mm deep.
              • Breakfast bars are deeper: 665mm or 900mm, for islands and overhangs.
              • Buy a length that covers your run, then cut it to fit.
              Full sizes and heights guide

              Why you’ll love it

              • A marble look in a shorter length

                At 3600mm, these tops match the length of the upstand and utility panel, so a straight run needs fewer offcuts. The decor itself is a marble effect.

              • Decorative edge on both faces

                The square edge carries laminate on both sides, so the front keeps the marble look. Underneath is chipboard, so cut ends and cut-outs need sealing.

              • Pieces to complete the room

                A 3600 x 125 x 18mm upstand and a 3600 x 350 x 18mm utility panel share the decor. So do a 3000 x 1200 x 8mm backsplash and a 5000mm edging roll.

              Marble look for compact, well-planned kitchens

              A 3600mm length covers a typical wall run in one piece, so smaller kitchens avoid joins altogether. Marble effect works with pale cabinets for a bright feel, or with dark fronts for contrast. The utility panel is the same length, which makes it handy for shelving or a laundry run. Carrera Marble is a good partner for chrome or black taps.

              View marble effect worktops

              How to fit

              Fitting Carrera Marble

              Carrera Marble is cut from 3600mm lengths, in 40mm and 25mm. A shorter top is easier to handle than a 4000mm one, but the decorative edge and the marble print still need protecting while you work.

              What you’ll need

              Most homes have these already:

              • Pencil
              • Drill driver
              • Circular saw or jigsaw
              • Straight edge or spirit level

              Tap to add the brands fitters use to your order:

              Rather not do it yourself? Any local kitchen fitter can fit it, and our team is happy to help on 0330 000 0000.

              Sizes and prices

              Prices include VAT and free delivery. Carrera Marble is supplied in full 3m and 4.1m lengths, uncut.

              ProductSize (L x D x T)Price
              Worktop 3.6m · 40mm square edge 3600 × 650 × 40mm £393.24
              Worktop 3.6m, 900 deep · 40mm square edge 3600 × 900 × 40mm £618.33
              Worktop 3.6m · 25mm square edge 3600 × 650 × 25mm £339.02
              Worktop 3.6m, 900 deep · 25mm square edge 3600 × 900 × 25mm £591.24
              Matching upstand · 3.6m 3600 × 125 × 18mm £78.67
              Matching splashback · Backsplash 3m 3000 × 1200 × 8mm £327.53
              Edging strip · 5m roll 5000mm £67.82
              Joining strips · Straight 38mm Aluminium, 38mm × 640mm £9.99
              Joining strips · Corner 38mm Aluminium, 38mm × 640mm £11.99
              Joining strips · Straight 22mm Aluminium, 22mm × 640mm £9.99
              Joining strips · Corner 22mm Aluminium, 22mm × 640mm £11.99
              End caps · Left 38mm Aluminium, 38mm × 640mm £7.99
              End caps · Right 38mm Aluminium, 38mm × 640mm £7.99
              End caps · Left 22mm Aluminium, 22mm × 640mm £7.99
              End caps · Right 22mm Aluminium, 22mm × 640mm £7.99
              Fitting kit · Joint kit 3 connector bolts + sealant £12.99

              Specification

              BrandTopShape
              EdgeDecorative square edge, laminated both sides
              Thickness40mm or 25mm
              Depth650mm, 900mm
              Lengths3600mm
              CoreChipboard core under a high-pressure laminate surface
              Matching upstand3600 x 125 x 18mm
              Matching splashback3000 x 1200 x 8mm
              WarrantyManufacturer’s warranty

              Questions about Carrera Marble

              Can’t find your answer? Contact our worktop team.

              0330 000 0000Email us
              How is Carrera Marble different from other TopShape marbles?

              The main difference is length: these tops are 3600mm, while most TopShape decors are 4000mm. Depths and thicknesses are the same.

              What is the matching upstand size?

              The upstand is 3600 x 125 x 18mm, the same length as the top. A 3000 x 1200 x 8mm backsplash and a 3600 x 350 x 18mm utility panel are also listed.

              Do I need to seal this like natural marble?

              No. It is a marble look in laminate, so the surface does not need sealing, but cut ends and the sink cut-out do need edging or silicone.

              Can I get a 900mm deep top?

              Yes. Both the 40mm and the 25mm tops come in 650mm and 900mm depths, all at 3600mm long, so you can mix depths along one run.

              Which finish do the handles and taps suit?

              Chrome and brushed steel suit pale marble looks, and black or brass suit it equally well. Choose cabinets in navy or white for a classic partnership.

              Is a carrara spelling used elsewhere?

              This TopShape decor is named Carrera Marble. A separate Carrara Marble laminate appears elsewhere in our range, so check the name when you order.

              More marble effect looks

              View all

              Kitchen Ideas, New Colours & The Odd Offer

              One email a month, written by people who know worktops. Unsubscribe whenever you like.

              By signing up you agree to receive marketing emails. Read our privacy policy.

              Your basket (0)

              Your basket is empty.

              Shop worktops

              Your delivery postcode

              We’ll use it to show your delivery dates across the site.